Lace-up hoisting grip for coaxial cable and waveguide
Lace-up hoisting grip is designed for middle part of the coaxial cable and elliptical waveguide, which is applied to wire's hauling, fixing and dragging. It provides an effective means for hoisting coax and elliptical waveguide into position and can be utilized to provide additional support once in place.
The lace-up design allows the hoisting grip to be attached even when the run has been connectorized and facilitates easy positioning at 200 (61m) increments on long coax runs.
 | General specifications |
Application | coax support |
Size | 1/4" to 6" |
Feature | Lace up at any point on coax |
Design | Open mesh with single eye support |
Material | Stainless steel 304 |
Include | Mesh Grip, Lacing wire, Installation instructions |
|
|
| Product code |
 | |
 | HG14-L |
This hoisting grip is appropriate to 1/4 in ATCB-B01 series RET cable, using 1.0mm stainless steel 304 material. | |
HG38-L | |
This hoisting grip is appropriate to 3/8 in coaxial cable or 8-12mm corrugated, smoothwall cable, CNT-400, LMR400 braided cable, using 1.0mm stainless steel 304 material. Sleeve length : 20cm | |
| |
| HG12-L |
This hoisting grip is appropriate to 1/2 in coaxial cable and elliptical waveguide 180 and 220, using 1.0mm stainless steel 304 material. Sleeve length : 25cm | |
HG58-L | |
This hoisting grip is appropriate to 5/8 in coaxial cable, elliptical waveguide 85, 90, 127, 132 and PWRT-608 and 21.9-22.2mm cable, using 1.2mm stainless steel 304 material. Sleeve length : 25cm | |
| |
| HG78-L |
This hoisting grip is appropriate to 7/8 in coaxial cable, 26-29mm cable, elliptical waveguide 77, and HELIAX cable, using 1.5mm stainless steel 304 material. Sleeve length : 34cm | |
HG114-L | |
This hoisting grip is appropriate to 1-1/4 in coaxial cable, 38-40mm cableand elliptical waveguide 64, using 1.5mm stainless steel 304 material. Sleeve length : 65cm | |
| |
 | HG158-L |
This hoisting grip is appropriate to 1-5/84 in coaxial cable and elliptical waveguide 44, 52, and 63, using 1.5mm stainless steel 304 material. Sleeve length : 70cm | |
HG214-L | |
This hoisting grip is appropriate to 2-1/4 in coaxial cable and elliptical waveguide 37, using 1.5mm stainless steel 304 material. Sleeve length : 90cm | |
| |
 | HG300-L |
This hoisting grip is appropriate to 3 in coaxial cable and elliptical waveguide 28 and 34, using stainless steel 304 material. | |
| HG400-L | |
This hoisting grip is appropriate to 4 in coaxial cable, using stainless steel 304 material. | |
| HG512-L | |
This hoisting grip is appropriate to 5-1/2 in coaxial cable, using stainless steel 304 material. | |
| HG600-L | |
| This hoisting grip is appropriate to 6 in coaxial cable, using stainless steel 304 material. |
You might also interested in :
Pre-laced Support Hoist Grip |
Non-conductive Cable Grip |
Fiber Optic Cable Set |
